Universal Joint Coupling: Correct installation and application method-Jiangsu Sitong Cardan Shaft Co.,Ltd
Welcome To Jiangsu Sitong! We are Professional Cardan shaft manufacturer.
  +86-18852632222 丨    lynn@cardanshaft.com.cn

Universal Joint Coupling: Correct installation and application method

Views:32     Author:Cardan Shaft Manufacturer     Publish Time: 2020-02-29      Origin:Sitong Cardan Shaft Co.,Ltd

The most important factor in a Universal Joint system is the technique of installation and applying the universal joint coupling. The various methods of applying the joints vary from one application to another. They can be a single joint or can consist of two or more joints. This will be determined by the project structure.


A single joint can result in a superior installation. However, when there are more joints than needed for a single application, it will lead to the poor performance of the joint. The disadvantages of the above-mentioned procedure are listed below. It is also noted that as the number of joints increases, the cost per joint also increases.


The disadvantage of this type of application is that it may take longer than other methods. If the joints are not applied perfectly, then the area of abrasion will be greater. The movement of the material, in this case, will lead to cracks that will remain. The joints should be smooth and not loose, it should be manufactured by utilizing standards and this can be made possible by following specific processes.


The application of the universal joint coupling by a single person could prove very risky. In this process, the joint is fixed in place and the difference between the two surfaces is measured. It is then necessary to make a line with the indicator points to determine the direction of deviation.


The disadvantage of this procedure is that it will require a great amount of work and effort. It is not recommended if the universal joint coupling is going to have to move laterally. The finished product must be subjected to strength testing before it is approved for use. The joints need to be measured accurately and even if a regular performance of the joint is needed, there may be a need for modifications. Again, if there are many joints that will be used, the consistency will have to be checked.


One should consider that the universal joint coupling need to be made by employing professionals and only by professional use will it provide better results. If one finds it difficult to make the joints, they can call on a car manufacturer to make the car joints for them. This will save a lot of time. One should always prefer the joints made by specialists since they are guaranteed to be of superior quality.


The disadvantage of this application is that it is a relatively expensive method. The amount that one will need to spend in order to purchase and set up a car jack will depend on the required space and type of car. There are some instances where the application of the joints is not required and it is suitable to use over the existing flooring material.


One has to remember that this method is only available for single joint applications. The other universal joint coupling application methods are required for composite applications. The advantages of using this type of application are the ease of use and cost-effectiveness.


The advantage of this type of application is that it provides for a single application and is guaranteed to be of superior quality. There are many advantages to using this method. One has to understand that this type of application will provide for a strong joint, which is ideal for hard-surfaced flooring. The joints can be made in two to three steps and this is usually a less time-consuming process.


The disadvantage of this application is that the surface where the joint will be fixed must be flat and even. In order to get the desired results, one needs to be careful in the selection of material. The finishing of the surfaces will have to be on par with the standard to achieve the maximum protection. It is always better to get advice from experts to know what type of surface should be used and how the surface should be polished.


The disadvantage of this application is that it is only applicable to single-joint applications. The joints do not hold together well when they are joined together. The fixing of the joints in place will not be easily done by a single person. It requires a great deal of experience to do the installations of the joints and this will result in lower costs of the process.


This type of application does not offer the advantages of universal joint coupling applications like reinforced floors, lifting beams, lightweight beams, seamless areas, etc. For these types of applications, it is advisable to use alternatives like the galvanized wall panels or the attached foam style joints. 


We have first-class production line and strict management system.

Contact Us

江苏四通机械制造有限公司
Jiangsu Sitong Cardan Shaft Co.,LTD
Tel : +86-523-84549777
Phone : +86-18852632222
E-mail : lynn@cardanshaft.com.cn
Whatsapp : +86-18852632222
Skype : sales@nskfagbearings.com
QQ : 510994342

Contact Us

Copyright 2020  Jiangsu Sitong Cardan Shaft Co.,Ltd All Rights Reserved. 网站地图 Sitemap